If your shop runs both fractional-inch and metric tools, inventory the shanks before buying an ER32 collet set. Start with the tools you use every week and record each diameter in the unit printed on the tool or datasheet. Compare that list with the sizes included in each set. That simple check can save bench time and reduce orders for sizes you already have.
Match the set to your holder and tool list
Confirm that your holder takes ER32 collets. Read the holder marking or check its part number. A marking such as CAT40-ER32 describes two interfaces. CAT40 identifies the spindle-side taper, and ER32 identifies the collet series. Verify both interfaces if you are replacing the holder as well as the collets.
Record the round shank diameter from the tooling specification. The cutting diameter on an end mill label can differ from its shank diameter. Where you have a choice between individual collets, check the manufacturer’s stated clamping range for that specific part.
Compare three PAC Tools USA sets
| ER32 set | Listed contents | Useful when |
|---|---|---|
| 290032 inch set | 21 pieces, 1/8 in to 3/4 in in 1/32 in steps | Most repeat jobs use fractional-inch shanks. |
| 290030 metric set | 18 pieces, 3 mm to 20 mm in 1 mm steps | Most repeat jobs use whole-millimeter shanks. |
| 290034 metric set | 35 pieces, 3 mm to 20 mm in 0.5 mm steps | Half-millimeter shanks recur across multiple jobs. |
For example, 1/4 in is 6.35 mm. A shop that regularly runs both 1/4 in and 6 mm shanks should list both in its inventory. Check the stated clamping range and application guidance before treating one collet as suitable for both.
Start with the sizes you use every week
If your work is mostly metric with a handful of repeat inch jobs, start with the metric set and price the individual inch collets that cover those jobs. If multiple operators share a machine and both unit systems are used daily, compare the cost of keeping two labeled sets at that machine with the cost of buying and managing loose collets.
Work through a mixed production schedule
Suppose a shop runs a recurring metric job with 6 mm, 10 mm and 12 mm shanks. Its repeat inch jobs use 1/4 in and 3/8 in. An engineering job also uses a 6.5 mm shank every few weeks. The buyer can use the following worksheet to compare kit contents against the actual tool list.
| Shank list | Nominal size coverage | Buying decision |
|---|---|---|
| 6, 10 and 12 mm | The 290030 and 290034 metric kits list whole-millimeter sizes in this range. | Use the 18-piece metric kit as the first option to price. |
| 1/4 and 3/8 in | Both nominal sizes fall on the 290032 fractional grid. | Price two individual inch collets and compare with the full inch kit. |
| 6.5 mm | The 290034 kit lists half-millimeter steps. The 290030 kit lists whole millimeters. | Price the specific 6.5 mm option or verify a listed collet’s approved range for this shank. |
This is a contents comparison. A nominal label identifies a size in the set. The collet maker’s published clamping range determines whether that particular collet can grip a given shank. Treat the range as a separate item on the purchase worksheet, especially when substituting a fractional size for a metric one.
Compare the cost of three stocking options
Price the 18-piece metric kit plus the three individual sizes, then compare that quote with an inch kit plus the same metric kit and any required additions. Finally, price the half-step metric kit plus the inch sizes. Ask which sizes are available now, which ones share a machine, and which missing sizes would stop a repeat order.
Measure the decision against coverage on repeat jobs. If the 6.5 mm shank is the only half-step size in use, the larger kit may add dozens of sizes with little immediate use. If engineering runs several half-step tools or multiple machines share the same crib, the larger kit may reduce follow-up purchasing. Record any outlier in the setup sheet so a replacement can be ordered before the next run.
Read the accuracy specification in context
PAC lists the three compared SKUs as standard precision. Its product pages also show the broader line’s standard, high and ultra precision options at a stated measurement distance. Check the exact SKU and test conditions when a drawing specifies runout. A collet grade describes the component under the supplier’s test method. The assembled tool also depends on the spindle, holder, nut, tool shank, stickout and cleanliness.
When comparing quoted runout values, ask where the measurement was taken. A reading near the holder is a different setup check from a reading farther along the shank. Follow the shop’s inspection procedure and record the measurement point with the result. That record helps the next operator reproduce the setup and compare replacement components.
Check coolant and assembly requirements
If the application calls for through-tool coolant, confirm whether it requires a sealed collet, a matching nut or another approved coolant arrangement. Check the individual product specification and the holder manufacturer’s instructions before adding the item to the order. The same ER series can be offered in different collet designs.
Follow the holder and nut manufacturer’s instructions for assembly, torque and tool engagement. For a conventional ER system, the manufacturer guidance linked in the publishing notes shows the collet engaging the nut before the assembly goes into the holder. Inspect the mating surfaces and replace damaged components according to your shop’s approved procedure.
Make reordering straightforward
Label storage by ER series, unit system and nominal size. Put the part number and grade on the setup sheet for recurring jobs. Keep the tool crib’s reorder point tied to the sizes that stop production when missing. For example, a frequently used 1/4 in collet may warrant a spare even when the rest of the inch kit rarely leaves the drawer.
Check the setup before you place the order
- Record the machine, spindle interface and existing holder or chuck part number.
- List the shank diameters, units and quantities. Mark frequently replaced tools separately.
- Check whether the job calls for a specific runout specification, coolant arrangement or collet type.
- Confirm which sizes the set contains and check the exact product listing for current price and availability.
Buying for a new machine? Compare the holder, collets and wrench together. PAC listsCNC tooling packages that include ER tooling for selected spindle interfaces. Review the package contents against your tool list and check which components your shop already has.
Shop PAC Tools USA ER Collets and Sets
Precision clamping solutions for mixed inch and metric CNC jobs
Shop PAC Tools USA ER collets and sets. For help with a mixed inch-and-metric order, send your holder part number and shank list to PAC Tools USA.
Frequently asked questions
Do inch and metric ER32 collets use the same holder?
Both can be used with a compatible ER32 holder and nut. Verify the specific collet type, the holder and nut specifications, and the rated clamping range for the tool shank.
Can an ER16 collet be fitted to an ER32 holder?
Use an ER32 collet in an ER32 holder. If the application calls for ER16, select a compatible ER16 holder for the machine’s spindle interface.
When does a single collet make more sense than a full set?
Order individual collets for a few repeat diameters or predictable replacements. A set is worth comparing when your job list spans several sizes in the same series.
Let’s Find the Right Tooling for Your Job!
Tell us about your CNC application, machine setup, or tooling requirement. Our team can help you identify the right solution for your machining needs.
About the Author: Scott Shippell
ISO 9001:2015 Certified CNC Tooling ExpertThis content is authored and reviewed by the technical engineering team at PAC Precision Tools USA. With over 20 years of experience in custom tooling manufacture, high-performance ER collets, shrink-fit systems, and hydraulic tool holders, our team provides certified expertise and adherence to precision engineering guidelines.
